4. Connecting to the Linux Server

Please refer to the diagram shown in the chapter Introduction for the addressing scheme used. Workstation 1 (W/S1) is on network 172.16.0.0 and can access the Linux server directly whereas Workstation 2 (W/S2) is on network 172.17.0.0 and needs to use the gateway (router) 172.17.0.254 to access the Linux box. This gateway information needs to be provided while configuring the clients only on W/S2. Netware refers to the gateway as 'ip_router'.

I am using W/S2 to illustrate the client setup. To setup W/S1 just change the address 172.17.0.5 to 172.16.0.5 and ignore all references to the gateway/router.

If you do not have a router you can skip the next section and proceed to

• Setup Netware Server if you use a Netware server.
• Setup MS Windows Client if you use the Microsoft Client.

4.1 Setup the Linux server

You may skip this section if you do not have a router.

You have to configure the Linux server to recognise the router thus allowing Workstation 2 to connect to the Web server. In order to setup the Linux server you should login as root. At the server prompt type

   route add gw default 172.16.0.254

ALT: You can add routes to the networks on the other side of the router. This would be done as

   route add -net 172.17.0.0 gw 172.16.0.254

4.2 Setup the Netware server

In order to setup the Netware server you should have Supervisor permissions or atleast Console operator permissions. If these cannot be got, try asking your Network Administrator to help you with the setup. At the Server enable the Ethernet_II frame type on the LAN by typing these commands or include them in the AUTOEXEC.ncf file.

   load NE2000 frame=Ethernet_II name=IPNET
   load TCPIP
   bind IP to IPNET addr=172.16.0.2 mask=FF.FF.FF.0

You might have to specify the slot or board number while loading the NE2000 driver depending on your machine configuration. (eg: load NE2000 slot=3 frame=.....)

4.3 Setup the Netware Client

On the PC you have the choice of Win3.1,WFWG or Win95. The installation procedure differs between Win95 and the older windows if you are using the 32bit client from Microsoft or Novell. If you are going to use the 16bit client, the procedure is the same and you can refer to the Windows 3.x installation instructions. For installing the 32bit client for Win95 skip to Windows 95 installation.

Windows 3.x

If you are using Win3.1 or WFWG you can install the Netware Client (VLMs) and some additional files which are provided with the TCP/IP diskette, namely

TCPIP.exe, VTCPIP.386, WINSOCK.dll and WLIBSOCK.dll

Note that the WINSOCK.dll file is different from the ones provided with Win95 and Trumpet. Install the Netware Client with the support for windows. Copy VTCPIP.386, WINSOCK.dll and WLIBSOCK.dll to the SYSTEM directory and TCPIP.exe to the NWCLIENT directory. Now modify the STARTNET.bat in the NWCLIENT directory to

   lsl
   ne2000     ---> your network card driver
   c:\windows\odihlp.exe     ---->if you are using WFWG
   ipxodi
   tcpip        ---> add this line
   nwip         ---> if you use Netware/IP
   vlm

Create a subdirectory (say) \NET\TCP and copy the files HOSTS, NETWORKS, PROTOCOLS and SERVICES from /etc on your Linux server or the directory SYS:ETC on your Netware server. Edit the copied HOSTS file to add the line for your new Linux server. This will enable you to refer to the Linux server as http://linux.mydomain/ instead of http://172.16.0.1/in your WWW browser

   127.0.0.1      localhost
   172.16.0.1      linux.mydomain

Edit the NET.cfg file in NWCLIENT directory

   Link Driver NE2000
       port 300
       int 3
       MEM D0000
       FRAME Ethernet_802.2

; ---- add these lines ----

      FRAME Ethernet_II

   Protocol TCPIP
      PATH TCP_CFG C:\NET\TCP
      ip_address  172.17.0.5
      ip_netmask  255.255.255.0
      ip_router   172.17.0.254     ---> add the address of your gateway only
                                  ---> if you have to use this
                                  ---> gateway to reach your HTTP server

   Link Support
      MemPool 6192       ---> the minimum is 1024. Try with different values
      Buffers 10 1580    ---> this again can be fine tuned

;---------------------------------
; You may need to add lines like these if you are using Netware/IP
;
   NWIP
      NWIP_DOMAIN_NAME  mydomain
      NSQ_BROADCAST   ON
      NWIP1_1 COMPATIBILITY   OFF
      AUTORETRIES     1
      AUTORETRY SECS  10

   [386Enh]
   .....
   network=*vnetbios, vipx.386, vnetware.386, VTCPIP.386
   .....

Reboot your PC, run STARTNET.bat and you can now use your favorite WWW browser to access your Web pages. You need not login to Netware and you don't have to run TCPMAN (if you use Trumpet Winsock).

Windows 95

This section explains how to install the 32bit client on Win95. Firstly you must install the following

   Client for Netware Networks (from Microsoft or Novell)
   Microsoft TCP/IP Protocol
   Network Adapter

To install these items, click on My Computer, Control Panel, Networks. Click Add. You will now be in a window that displays Client, Adapter, Protocol and Service. To install the Client for Netware Networks:

  1. DoubleClick on Client
  2. Click on Microsoft or Novell
  3. DoubleClick on Client for Netware Networks

To install the TCP/IP Protocol:

  1. DoubleClick on Protocol
  2. Click on Microsoft
  3. DoubleClick on TCP/IP

Windows 95 by default installs several other protocols automatically. Remove them by clicking on them and clicking the Remove button. Typically Win95 installs the Microsoft NetBeui protocol, and IPX/SPX compatible protocol. You can delete the NetBEUI protocol, but you will need the IPX/SPX protocol if you wish to login to the Netware Server.

To setup TCP/IP click on TCP/IP, click on Properties, click on the tab IP address

  Enter your IP address in the "Specify an IP address "
                        box as 172.17.0.5
  In the Subnet Mask box enter 255.255.255.0

  Enter your gateway (router) address in the box New gateway
     as 172.17.0.254
  Click the Add button

You should get a message to reboot. Do so. You should now be able to use the Browser to connect to your HTTP Server.

4.4 Setup Microsoft Client

If you are using the Microsoft Client for accessing your network, then this section details how to install TCP/IP for

• Windows for Workgroups (WFWG)
• Windows 95
• Windows NT 4.0

   127.0.0.1      localhost
   172.16.0.1     linux.mydomain

   172.16.0.2     netware.mydomain
   172.16.0.3     winNT.mydomain
   172.16.0.5     ws_1

Windows for Workgroups

This section explains how to install the 32bit client on WFWG. Firstly you must download the TCP/IP drivers for Windows from Microsoft. The current version is 3.11b and is available at ftp://ftp.microsoft.com or other sites as tcp32b.exe. Make sure that you have load Win32s before trying to load the TCP/IP-32bit driver.

Having expanded the TCP/IP files into a temporary directory (say C:\TEMP), check your \WINDOWS\SYSTEM directory for copies of OEMSETUP.INF. If there are any, rename them. Now copy the OEMSETUP.INF file from the TEMP directory to the \WINDOWS\SYSTEM directory. If you have loaded any other TCP/IP stacks on your system, please remove them before you proceed.

Start Network Setup or Windows Setup/Change Network settings

    Click the Networks button
    Click Install Microsoft Windows Network.
      Choose support for additional networks (if required)
    Click OK

     Click the Adapter button
         select an adapter (say NE2000)
         Click OK
     Click the Protocol button
         select the MS TCP/IP-32 protocol
         click OK

   In the IP address box enter 172.17.0.5
   In the Subnet Mask box enter 255.255.255.0
   Enter your gateway (router) address in the box default gateway
     as 172.17.0.254

Windows 95

This section explains how to install the 32bit client for Microsoft on Win95. Firstly you must install the following

   Client for Microsoft Networks
   Microsoft TCP/IP Protocol
   Network Adapter

To install these items, click on My Computer, Control Panel, Networks. Click Add. You will now be in a window that displays Client, Adapter, Protocol and Service. To install the Client for Microsoft Networks:

  1. DoubleClick on Client
  2. Click on Microsoft
  3. DoubleClick on Client for Microsoft Networks

To install the TCP/IP Protocol:

  1. DoubleClick on Protocol
  2. Click on Microsoft
  3. DoubleClick on TCP/IP

Windows 95 by default installs several protocols automatically. Remove them by clicking on them and clicking the Remove button. Typically Win95 installs the Microsoft NetBeui protocol.

To setup TCP/IP click on TCP/IP, click on Properties, click on the tab IP address

  Enter your IP address in the "Specify an IP address "
                        box as 172.17.0.5
  In the Subnet Mask box enter 255.255.255.0

  Enter your gateway (router) address in the box New gateway
     as 172.17.0.254
  Click the Add button

You should get a message to reboot. Do so. You should now be able to use the Browser to connect to your HTTP Server.

Windows NT

This section details how to Install the TCP/IP client for WinNT 4.0. Start Control Panel/ Network

    Select the Adapter tab.
        Click Add to add a new adapter (if you don't have one)

    Select the Protocols tab
        Click Add
        Select the TCP/IP protocol
        Click OK

   Select the tab IP Address
      Mark the checkbox 'Specify an IP address'
      In the IP address box enter 172.17.0.5
      In the Subnet Mask box enter 255.255.255.0
      Enter your gateway (router) address in the box Default Gateway
          as 172.17.0.254

4.5 Setup TCP/IP on Macintosh

If you are using the Macintosh for accessing your network, then this section details how to install MacTCP for the PowerMacs.

Note: To enable you to refer to the Linux server as http://linux.mydomain/ instead of http://172.16.0.1/ in the WWW browser and all your intranet commands you need to edit the hosts file. The format of the hosts file is different from the one used in Unix. The Mac hosts file is based on RFC-1035. You can add more entries for each of your other hosts (Netware, Unix, WinNT) as well. The MacOS keeps its HOSTS file in the Preferences folder under the System folder. Edit this file and add a line for your Linux server as:

  linux.mydomain    A  172.16.0.1

  netware.mydomain  A  172.16.0.2
  winNT.mydomain    A  172.16.0.3
  ws_1              A  172.16.0.5

MacTCP

This section explains how to install MacTCP. Firstly you must download the MacTCP files from Apple or install it from the Internet Connection CD. To configure MacTCP, click the Apple Menu/ Control Panels/ TCP/IP. In the screen change the setting for 'Connect via:' to 'Ethernet'

Change the 'Configure' setting to 'Manually'

  In the IP address box enter 172.17.0.5
  In the Subnet Mask box enter 255.255.255.0
  Enter your gateway (router) address in the box
    Router address as 172.17.0.254